By Yavay Team ·
How to Measure Windows for Roller Shades: Inside and Outside Mount (2026)
Measure a window the way a shade dealer orders it: three widths, three heights, the recess depth, inside versus outside mount, sliding doors, the mistakes that cost a reorder, and a printable worksheet.
Custom roller shades are cut to the numbers you send, so the measuring is the order. Dealers measure every window three times across and three times down, note how deep the opening is, and write each number to the nearest ⅛ inch. This guide walks through that routine for an inside mount, an outside mount and a sliding door, lists the mistakes that turn into a reorder, and ends with a worksheet you can print and take to the window.
You need: a steel tape measure (a cloth tape stretches), a pencil, and the worksheet below. Measure every window on its own, even the ones that look identical: in most homes they aren't.
First decide: inside mount or outside mount
Where the shade mounts changes what you measure, so decide this before you pick up the tape.
- Inside mount sits inside the window opening, flush with the wall or just proud of it. It is the cleaner look, it shows off the trim, and it leaves the sill free. It needs enough depth in the opening for the roller and its brackets, and because the fabric is narrower than the roller, a little light shows at each side.
- Outside mount fixes to the wall or trim above the window and overlaps the opening on every side. It covers more light, hides a window that is out of square, and works on shallow openings, French doors and windows with cranks or handles in the way. The shade looks larger, and it covers the trim.
Check the depth first. Measure from the face of the wall straight back to the glass, or to whatever sticks out first: a crank, a tilt latch, a security sensor. Most roller shades need about 1½ to 2 inches of flat depth to mount inside, and 2½ to 3½ inches to sit fully flush. If the opening is shallower than the product's minimum, or more than about ½ inch out of square, go with an outside mount.
Measuring for an inside mount
Measure the opening itself, from the inside face of one jamb to the inside face of the other, not the glass and not the trim. Record every number as you read it, to the nearest ⅛ inch, with no deductions.
Width: top, middle, bottom
Hook the tape on one jamb and read it at the other, three times: near the top of the opening, across the middle, and near the sill. Write all three on the worksheet. The shade is ordered to the narrowest of the three, so it clears the opening at its tightest point.
Height: left, centre, right
Measure from the top of the opening down to the sill on the left side, in the centre, and on the right side. If the window has no sill, measure to where you want the shade to end. The shade is ordered to the longest of the three, so it reaches the sill everywhere.
Depth and obstructions
Write down the depth you checked earlier and anything inside the opening the roller could hit. Note which side you want the control chain or motor on, and whether anything, a faucet or a counter, is in the way of the chain.
Send the opening size and say "inside mount". The manufacturer takes about ¼ to ½ inch off for the brackets and clearance. If you take it off too, the shade arrives with a gap on both sides.
Measuring for an outside mount
For an outside mount you measure the area you want the shade to cover, and that is the size you order.
- Width: the opening (or the trim, if the shade will cover it) plus 1½ to 2 inches on each side, so 3 to 4 inches more than the opening in all. Overlap more if the shade is for privacy or blackout.
- Height: from where the brackets will sit, usually 2 to 3 inches above the opening or trim, down to the sill, or 2 inches below it if there is no sill or you want it covered.
- Mounting surface: the brackets need a flat strip at the top. If the trim is proud of the wall, either mount on the trim or allow for a spacer so the shade hangs plumb.
On a roller shade the fabric is about 1 to 1½ inches narrower than the ordered width, because the brackets and roller ends take up the difference. Allow for that when you decide how much to overlap.
Sliding doors, French doors and banks of windows
Wide openings are where most measuring goes wrong, because there are two correct answers and they need different numbers.
- One shade per panel keeps each shade light and lets you raise one side at a time. Measure each panel's width between the frame's mullions (the vertical bars) and its height from the top of the opening to the floor or track, and order each shade separately, so every split lands on a mullion and every shade has its own roller box. This is how Yavay renders them for dealers: a three-panel door prices and renders as three shades.
- One shade across the whole door is simpler to operate and blocks more light. Measure the full opening and add the outside-mount overlap, and leave ½ inch of clearance above the floor so the hem never drags.
Either way, note which panel slides, where the handle sits and how far it projects. A handle that stands more than the shade's depth off the glass rules out an inside mount on that panel.
Mistakes that turn into a reorder
- Measuring one window and ordering for all of them. Openings in the same room routinely differ by ¼ inch or more.
- Rounding. Write 35⅞, not 36. Custom shades are cut to the eighth.
- Deducting for an inside mount. The maker does it. Doing it twice leaves gaps.
- Measuring the glass or the trim instead of the opening. For an inside mount, it is jamb to jamb.
- Forgetting depth. The shade fits the width and height and then hits the crank handle.
- Swapping width and height. Always write width first, then height, and label the columns.
- A cloth or worn tape. Use a steel tape with a hook that isn't bent.
Measuring with an iPhone
Yavay's iPhone app (early access, on iPhones with LiDAR) does this routine from a room scan. After the scan it photographs each window, you drag the corners to the opening you want measured, and it reports the three widths, the three heights and the recess depth to ⅛ inch, on an annotated photo of the window and on a printable measurement sheet in feet and inches, with doors and whole walls listed beside the windows. Dealers use the sheet to render the shades in the customer's own photo at those sizes and price them from their grid. The final size is still confirmed with a tape before the order, which is also what a dealer does after a home visit.
If you are measuring for wallpaper as well, the same scan lists each wall's width, height and the area left to paper. The wallpaper roll calculator turns those into a roll count.
Printable window measurement worksheet
Take this to the window. One row per window, every number to the nearest ⅛ in.
Window measurement worksheet
Room: ____________________ Date: ____________ Measured by: ____________________
| Window | Mount in / out | Width (in) | Height (in) | Depth wall to glass | Obstructions / notes | ||||
|---|---|---|---|---|---|---|---|---|---|
| Top | Middle | Bottom | Left | Centre | Right | ||||
| 1. | |||||||||
| 2. | |||||||||
| 3. | |||||||||
| 4. | |||||||||
| 5. | |||||||||
| 6. | |||||||||
Inside mount: order the narrowest width and the longest height, with no deductions. Outside mount: order the size you want the shade to be, overlapping the opening 1½–2 in each side and 2–3 in above. Width always comes first. Worksheet from yavay.app/guides/how-to-measure-windows-for-roller-shades
Measuring for roller shades: FAQs
Do I use the smallest or the largest measurement for an inside mount?
The narrowest of the three widths and the longest of the three heights. The shade has to clear the opening at its tightest point, and it has to reach the sill at the tallest point. Write all three down anyway: a window that differs by more than about 1/2 inch top to bottom is out of square, and an outside mount will look better on it.
Should I deduct anything for an inside-mount roller shade?
No. Give the manufacturer or dealer the exact opening size and say it is an inside mount. They take the deduction for the brackets and clearance themselves, usually 1/4 to 1/2 inch in all. If you deduct as well, the shade arrives with a gap on each side.
How much depth does an inside-mount roller shade need?
It depends on the shade's roller diameter and bracket. Most roller shades need about 1 1/2 to 2 inches of flat, unobstructed depth to mount inside the opening, and 2 1/2 to 3 1/2 inches to sit fully flush with the wall. Larger shades and motorized rollers need more. Check the product's own minimum depth, and measure from the wall face to the nearest obstruction (the glass, a crank handle or a tilt latch), not just to the frame.
How much should an outside-mount shade overlap the window?
Add 1 1/2 to 2 inches to each side of the opening (3 to 4 inches in total) and 2 to 3 inches above it for the bracket, so the width you order is the opening plus the overlap. For privacy or blackout, overlap more. Make sure the wall or trim where the brackets land is flat.
How do I measure a sliding glass door for roller shades?
Decide whether you want one shade per panel or one shade across the whole door. For one per panel, measure each panel's width between the frame's mullions and its height from the top of the opening to the floor or track, then order each shade separately so the splits land on the mullions. For one wide shade, measure the whole opening and add the outside-mount overlap, and leave 1/2 inch of clearance above the floor so the hem doesn't drag. Note which way the door slides and where the handle sits.
How accurate do window measurements for shades need to be?
To the nearest 1/8 inch. Custom shades are cut to the number you send, and a 1/4 inch error on an inside mount is visible as a light gap or a shade that won't fit the opening. Use a steel tape, not a cloth one, and write the number down as you read it rather than rounding.